SAE J518 code 62 Flange Split Clamps FS series

SAE J518 code 62 Flange Split Clamps FS series

0
Views: 2,655
E-mail : Swintool@aliyun.com

Product Details

Instruction for code 62 Flange Clamps one piece type:

 

1.Working pressureof SAE code 62 series flange clamps is 42 MPa (420 bar).

 

2.SAE Flange clamps dimensionsis according to ISO 6162-2:2012. ISO Nominal Size: DN 13; DN 19; DN 25; DN 32; DN 38; DN 51; DN 64; DN 76; DN 89; DN 102; DN 127; Inch size: 1/2";3/4";1";1 1/4";1 1/2";2";2 1/2";3".

 

3.Material of SAE one-piece flange clamp is made of carbon steel C45, Stainless steel 304, 316 or 316L.

 

4.The external surface Corrosion protectionof all carbon steel flange clamps,shall be protected with an appropriate coating to pass a minimum 72-h salt spray test in accordance with ISO 9227.

 

5.Test requirement for pressure/temperature: Flange type connections conforming to this part of ISO 6162 shall be subjected to the burst and cyclic endurance tests specified in ISO 19879 to verify that they meet the specified pressure/temperature requirements.

It shall be suitable for use at the working pressures given in Tables 2 when used at temperatures between -40 °C and +120 °C. Flange connections conforming to this part of ISO 6162 shall not be assembled at temperatures lower than -20 °C.

 

6.Designation ofone piece flange clamps connections

One-piece flange clamp of size DN 25:  Clamp ISO 6162-2, FCS×25

Swintool company use FS-16(dash size)W: SAE 6000 psi flange clamps size 1” inch.

Parker company use FUS6x(2,3,4,5,6,8, etc) and FCC (dash size FCCT2 )

Stauff company use BM-60x(1,2,3,4,5,6,7,8,9,10,11)

 

7.SAE SPLIT FLANGE HALVES CLAMP-code 62 SAE 6000 PSI Dimensions

 

 

 

PART NO.

FLANGE SIZE

BOLT

 DIMENSIONS

A

B

C

D

E

FL-08

1/2"

M8x30

56.3

47

40.5

9

18.2

FL-12

3/4"

M10x35

71.4

60

50.8

11

23.8

FL-16

1"

M12x45

80.9

70

57.1

13

27.8

FL-20

1.1/4"

M14x30

95.2

77

66.7

15

31.8

FL-24

1.1/2"

M16x55

112.7

95

79.5

17

36.5

FL-32

2"

M20x70

133.3

114

96.8

21

44.5

 

 

Assembled flange connection with split flange clamp (FCS or FCSM)

 

 

 

 

Dimensions, torques and maximum working pressures for split flange assemblies for use with inch screws 

 

 

Dimensions in mullimetres unless noted

Nominal
size

DN

d1

+0
-1.5

d2

 

Max.

O-ring
size
codea

Flat
washerb

(recom -
mended)

Type 2 - inch screws of grade 8 in
accordance with SAE J429

Maximum
working
pressure

 

MPa (bar)

Minimum
burst
pressure

 

MPa (bar)

d3
Screw
threadc

UNC

l1
Screw
lengthd

nom.

l2

 

Min. full
thread

Screw
torquee
(N·m)
+10%
-0

13

13.0

13.0

210

M8

5/16-18

32

20

32

35 (350)

140 (1 400)

19

19.2

19.2

214

M10

3/8-16

32

22

60

35 (350)

140 (1 400)

25

25.6

25.6

219

M10

3/8-16

32

22

60

32 (320)

128 (1 280)

32

32.0

32.0

222

7/16 b

7/16-14

38

25

92

28 (280)

112(1 120)

38

38.2

38.2

225

M12

1/2-13

38

27

150

21 (210)

84 (840)

 

 

 

 

 

 

 

 

 

 

 

51

51.0

51.0

228

M12

1/2-13

38

27

150

21 (210)

84 (840)

64

63.5

63.5

232

M12

1/2-13

44

27

150

17.5 (175)

70 (700)

76

76.2

76.2

237

M16

5/8-11

44

30

295

16(160)

64 (640)

89

89.0

89.0

241

M16

5/8-11

51

30

295

3.5 (35)

14 (140)

102

101.6

101.6

245

M16

5/8-11

51

30

295

3.5 (35)

14 (140)

127

127.0

127.0

253

M16

5/8-11

57

30

295

3.5 (35)

14 (140)

   

    WARNING-It is important that all screws be lightly torqued before applying the final recommended torque values to avoid breaking the split

    flange clamps or one-piece flange clamps during installation (see Annex A for assembly guidelines).         

      

    a    O-ring size code in accordance with ISO 3601-1; see Annex B for reference dimensions.            

 

    b    ANSI/ASNE B18.22.1 Type B narrow washers of HV 300 quality material for the corresponding screw size in this table may be substituted for all sizes

    except for DN32, where a washer conforming to ISO 7089 might cause interference.

                                              

    c    Coarse pitch thread in accordance with ISO 263 and ISO 725(UNC-2A for screw threads, UNC-2B for port threads).

    

    d    Screw lengths are calculated for steel; use of other materials can require different screw lengths.

    

    e    These torque values are only a guide when using lubricated screws, calculated with a coefficient of friction of 0,17. Net tightening torque

    depends on many factors, including lubrication, coating and surface finish.

 

 

 

Leave a Message