SAE J518 code 62 Flange Clamps FS series

SAE J518 code 62 Flange Clamps FS series

0
Views: 3,335
E-mail : Swintool@aliyun.com

Product Details

Instruction for code 62 Flange Clamps one piece type:

  

1. Working pressure of SAE code 62 series flange clamps is 42 MPa (420 bar)

 

2. SAE Flange clamps dimensions is according to ISO 6162-2:2012.

ISO Nominal Size: DN 13;DN 19; DN 25; DN 32; DN 38; DN 51; DN 64; DN 76; DN 89; DN 102; DN 127;

Inch size: 1/2";3/4";1";1 1/4";1 1/2";2";2 1/2";3".

 

3. Material of SAE one-piece flange clamp is made of carbon steel C45 ,Stainless steel 304,316 or 316L.

 

4. The external surface Corrosion protection of all carbon steel flange clamps,shall beprotected with an appropriate coating to pass a minimum 72-h salt spray test in accordance with ISO 9227.
 

5. Test requirement for pressure/temperature: Flange type connections conforming to this part of ISO 6162 shall be subjected to the burst and cyclic endurance tests specified in ISO 19879 to verify that they meet the specified pressure/temperature requirements.

 

6. Designation of one piece flange clamps connections 

One-piece flange clamp of size DN 25: Clamp ISO 6162-1, FC×25 

Swintool company use FL-16(dash size)W: SAE 3000 psi flange clamps size 1” inch. 

Parker company use FUS6x(2,3,4,5,6,8, etc) and FCC (dash size FCCT2 ) 

Stauff company use BM-60x(1,2,3,4,5,6,7,8,9,10,11)

 

7. Dimensions of SAE Flange Clamps Code 62

 

 

 

 

 

PART NO.

FLANGE SIZE

BOLT

 DIMENSIONS

A

B

M

d

N

h

FL-08W

1/2"

M8x30

56.3

47

40.5

9

18.2

7.2

FL-12W

3/4"

M10x35

71.4

60

50.8

11

23.8

8.2

FL-16W

1"

M12x45

80.9

70

57.1

13

27.8

9

FL-20W

1.1/4"

M14x30

95.2

77

66.7

15

31.8

9.8

FL-24W

1.1/2"

M16x55

112.7

112.7

79.5

17

36.5

12

FL-32W

2"

M20x70

133.3

114

96.8

21

44.5

12

 

 

Assembled flange connection with one-piece flange clamp (FC or FCM)

 

 

 

Dimensions, torques and maximum working pressures for one-piece flange assemblies for use with inch screws

 

 

 

Dimensions in mullimetres unless noted

Nominal
size

DN

d1

+0
-1.5

d2

 

Max.

O-ring
size
codea

Flat
washerb

(recom -
mended)

Type 2 - inch screws of grade 8 in
accordance with SAE J429

Maximum
working
pressure

 

MPa (bar)

Minimum
burst
pressure

 

MPa (bar)

d3
Screw
threadc

UNC

l1
Screw
lengthd

nom.

l2

 

Min. full
thread

Screw
torquee
(N·m)
+10%
-0

13

13.0

13.0

210

M8

M8

30

16

32

42(420)

168(1 680)

19

19.2

19.2

214

M10

M10

35

18

70

42(420)

168(1 680)

25

25.6

25.6

219

M12c

M12

45

23

130

42(420)

168(1 680)

 

 

 

 

 

 

 

 

 

 

 

32

32.0

32.0

222

M12

M12

45

23

130

42(420)

168(1 680)

38

38.2

38.2

225

M16

M16

55

27

295

42(420)

168(1 680)

51

51.0

51.0

228

M20

M20

70

35

550

42(420)

168(1 680)

 

 

 

 

 

 

 

 

 

 

 

64

63.5

63

232

M24

M24

80

50

550

42(420)

168(1 680)

76

76.2

76

237

M30

M30

90

60

650

42(420)

168(1 680)

   

    WARNING——It is important that all screws be lightly torqued before applying the final recommended torque values to avoid breaking the split 

    flange clamps or one-piece flange clamps during installation (see Annex A for assembly guidelines).         

      

    a    See definition in ISO 5598.

 

    b    O-ring size code in accordance with ISO 3601-1;see Annex B for reference dimensions.

                                              

    c    ANS/ASME B18.22.1 Type B narrow washers of HV 300 quality material sized for the corresponding inch screw specified in Table 2 may be substituted for all

    but the DN 25 size, where a 7/16 washer in accordance with ANSI/ASME B18.22.1 might cause interference.

    

    d    Coarse pitch thread in accordance with ISO 261 and ISO 724.

    

    e    Screw lengths are calculated for steel;use of other materials can require different screw lengths.

 

     f     These torque values are only a guide when using lubricated screws, calculated with a coefficient of friction of 0,17. Net tightening torque depends on many

    factors, including lubrication, coating and surface finish.

 

 

Leave a Message