SAE code 61 Split Flange Clamps FL series

SAE code 61 Split Flange Clamps FL series

0
Views: 3,089
E-mail : Swintool@aliyun.com

Product Details

Instruction for code 61 Flange Clamps one piece type:

 

1.Working pressureof SAE code 61 series flange clamps is 3000 PSI, 3,5 MPa (35 bar) to 35 MPa (350 bar).

 

2.SAE Flange clamps dimensionsis according to ISO 6162-1:2012. ISO Nominal Size: DN 13; DN 19; DN 25; DN 32; DN 38; DN 51; DN 64; DN 76; DN 89; DN 102; DN 127; Inch size: 1/2";3/4";1";1 1/4";1 1/2";2";2 1/2";3".

 

3.Material of SAE one-piece flange clamp is made of carbon steel C45. Stainless steel.  

 

4.The external surface Corrosion protectionof all carbon steel flange clamps,shall be protected with an appropriate coating to pass a minimum 72-h salt spray test in accordance with ISO 9227.

 

5.Test requirement for pressure/temperature: Flange type connections conforming to this

part of ISO 6162 shall be subjected to the burst and cyclic endurance tests specified in ISO

19879 to verify that they meet the specified pressure/temperature requirements.

It shall be suitable for use at the working pressures given in Tables 2 when used at

temperatures between -40 °C and +120 °C. Flange connections conforming to this part

of ISO 6162 shall not be assembled at temperatures lower than -20 °C.

 

6.Designation ofone piece flange clamps connections

One-piece flange clamp of size DN 25:  Clamp ISO 6162-1, FCS×25

 

7.Dimension of SAE split Flange Clamp code 61

 

 

 

 

PART NO.

FLANGE SIZE

BOLT

 DIMENSIONS

A

B

M

d

N

FL-08

1/2"

M8x25

54

46

38.1

9

17.5

FL-12

3/4"

M10x30

65.1

52

47.6

11

22.2

FL-16

1"

M10x30

69.8

59

52.4

11

26.2

FL-20

1.1/4"

M10x30

79.4

73

58.7

11

30.2

FL-24

1.1/2"

M12x35

93.7

83

69.8

13.5

35.7

FL-32

2"

M12x35

101.6

97

77.8

13.5

42.9

FL-40

2.1/4"

M12x40

114

108

89

13.5

50.8

FL-48 3" M16x50 135 130.6 106.4 16.7 62

 

 

Dimensions, torques and maximum working pressures for one-piece flange assemblies for use with inch screws

 

 

 

Dimensions in mullimetres unless noted

Nominal
size

DN

d1

+0
-1.5

d2

 

Max.

O-ring
size
codea

Flat
washerb

(recom -
mended)

Type 2 - inch screws of grade 8 in
accordance with SAE J429

Maximum
working
pressure

 

MPa (bar)

Minimum
burst
pressure

 

MPa (bar)

d3
Screw
threadc

UNC

l1
Screw
lengthd

nom.

l2

 

Min. full
thread

Screw
torquee
(N·m)
+10%
-0

13

13.0

13.0

210

M8

5/16-18

32

20

32

35 (350)

140 (1 400)

19

19.2

19.2

214

M10

3/8-16

32

22

60

35 (350)

140 (1 400)

25

25.6

25.6

219

M10

3/8-16

32

22

60

32 (320)

128 (1 280)

32

32.0

32.0

222

7/16 b

7/16-14

38

25

92

28 (280)

112(1 120)

38

38.2

38.2

225

M12

1/2-13

38

27

150

21 (210)

84 (840)

 

 

 

 

 

 

 

 

 

 

 

51

51.0

51.0

228

M12

1/2-13

38

27

150

21 (210)

84 (840)

64

63.5

63.5

232

M12

1/2-13

44

27

150

17.5 (175)

70 (700)

76

76.2

76.2

237

M16

5/8-11

44

30

295

16(160)

64 (640)

89

89.0

89.0

241

M16

5/8-11

51

30

295

3.5 (35)

14 (140)

102

101.6

101.6

245

M16

5/8-11

51

30

295

3.5 (35)

14 (140)

127

127.0

127.0

253

M16

5/8-11

57

30

295

3.5 (35)

14 (140)

   

    WARNING——It is important that all screws be lightly torqued before applying the final recommended torque values to avoid breaking the split 

    flange clamps or one-piece flange clamps during installation (see Annex A for assembly guidelines).         

      

    a    See definition in ISO 5598.

 

    b    O-ring size code in accordance with ISO 3601-1;see Annex B for reference dimensions.

                                              

    c    ANS/ASME B18.22.1 Type B narrow washers of HV 300 quality material sized for the corresponding inch screw specified in Table 2 may be substituted for all

    but the DN 25 size, where a 7/16 washer in accordance with ANSI/ASME B18.22.1 might cause interference.

    

    d    Coarse pitch thread in accordance with ISO 261 and ISO 724.

    

    e    Screw lengths are calculated for steel;use of other materials can require different screw lengths.

 

     f     These torque values are only a guide when using lubricated screws, calculated with a coefficient of friction of 0,17. Net tightening torque depends on many

    factors, including lubrication, coating and surface finish.

 

Leave a Message