Instruction for code 61 Flange Clamps one piece type tapped:
1.Working pressure of SAE code 61 series flange clamps is 3000 PSI, 3,5 MPa (35 bar) to 35 MPa (350 bar).
2.SAE Flange clamps dimensionsis according to ISO 6162-1:2012. ISO Nominal Size: DN 13; DN 19; DN 25; DN 32; DN 38; DN 51; DN 64; DN 76; DN 89; DN 102; DN 127; Inch size: 1/2";3/4";1";1 1/4";1 1/2";2";2 1/2";3".
3.Material of SAE one-piece flange clamp is made of carbon steel C45 ,Stainless steel 304,316 or 316L.
4.The external surface Corrosion protection of all carbon steel flange clamps,shall be protected with an appropriate coating to pass a minimum 72-h salt spray test in accordance with ISO 9227.
5.Test requirement for pressure/temperature: Flange type connections conforming to this part of ISO 6162 shall be subjected to the burst and cyclic endurance tests specified in ISO 19879 to verify that they meet the specified pressure/temperature requirements.
6.Designation ofone piece flange clamps connections
Clamp ISO 6162-2, FCM×25
One-piece flange clamp size DN 25 to be used only with metric screws (type 1)
Clamp ISO 6162-2, FC×25
One-piece flange clamp size DN 25 to be used only with inch screws (type 2)
Swintool company use FL-16(dash size)W: SAE 3000 psi flange clamps size 1” inch.
Parker company use FUS3x(2,3,4,5,6,8, etc) and FCC (dash size FCCT1 )
Stauff company use BM-Gx(1,2,3,4,5,6,7,8,9,10,11)
SAE Flange Clamp with Metric thread
FL-xxWM
Stauff SAE Flange Clamp Metric Holes no. BM-G FL-xxWU with Inch screw UNF thread
PART NO. |
FLANGE SIZE |
DIMENSIONS |
|||||
A |
B |
d |
h |
M |
N |
||
FL-08WM |
12" |
54 |
45.6 |
M8 |
6.2 |
38.1 |
17.5 |
FL-12WM |
34" |
65 |
51.8 |
M10 |
6.2 |
47.6 |
22.2 |
FL-16WM |
1" |
70 |
58.4 |
M10 |
7.5 |
52.4 |
26.2 |
FL-20WM |
1.14" |
79 |
72.6 |
M10 |
7.5 |
58.7 |
30.2 |
FL-24WM |
1.12" |
94 |
82.2 |
M12 |
7.5 |
69.9 |
35.7 |
FL-32WM |
2" |
102 |
96.4 |
M12 |
9 |
77.8 |
42.9 |
FL-40WM |
2.12" |
114 |
108.2 |
M12 |
9 |
88.9 |
50.8 |
FL-48WM |
3" |
135 |
130.6 |
M16 |
9 |
106.4 |
61.9 |
Note:
1.Metric thread is Coarse pitch thread in accordance with ISO 261 and ISO 724.
SAE Flange Clamp with UNC Tapped hole
FL-xxWU
UNC thread is Coarse pitch thread in accordance with ISO 263 and ISO 725 (UNC-2A for screw threads, UNC-2B for port threads).